OpenBSD Soekris Read Only Root

From WTFwiki
Revision as of 13:15, 7 September 2010 by Jontow (talk | contribs) (typos)
Jump to navigation Jump to search

Running OpenBSD on a Soekris net4801 / net5501

Introduction/Theory

A number of ways exist to do this, I've chosen the slightly more complicated but fairly rewarding method of
running with the root (only) filesystem mounted read-only. This means the compact-flash card will live a
little longer, not enduring the write cycles that are fabled to kill them, and if someone trips over the power
cord, you don't lose anything on the filesystems. You also never need to endure the delay of a lengthy fsck(8).

All the bonuses out of the way: it's kind of a bastard to setup.. I'll try my best to detail it, including a
replacement for '/etc/rc'. There are a number of "neat" tricks to play with symbolic links and MFS style
RAM-disks.

Installation

Perform a PXE-boot standard OpenBSD/i386 install, the following differences apply:
Power on your soekris with a serial console connected. They use a standard DB9M connector, and supply 19200 baud, 8n1.
If you don't know what that means, figure it out via google or wikipedia.

At some point, the soekris' BIOS will ask you to hit Ctrl+P to interrupt the boot and enter the monitor, do so, and at
the prompt, type "boot F0". "F0" is the name of the first ethernet port on the device.

You should see the soekris come up with an address via DHCP, and put you at an OpenBSD PXE boot loader prompt, you should
type the following to ensure a successful boot.. order matters:

 > stty com0 19200
 > set tty com0
 > boot bsd.rd


You should see the kernel boot, just wait until it comes to the Install, Upgrade, etc menu; it will take a minute or a few.

Choose 'Install', and proceed as any normal OpenBSD install would, with some exceptions:

  • When installing, you should partition your CF card with 1 giant / partition, and *no swap*
  • It'll ask you later on if you want to change the console to com0, tell it yes and choose 19200 to match the soekris BIOS settings.
  • Once installed, reboot into your installation and do basic post-install configuration, including setting up network interfaces, adding packages, configuring sudo, etc.. the idea is to have a fully installed system that just needs configuration.


Post-Install Madness

Some general good-idea step are in order:

  • Add yourself a user, and configure sudo(8) properly for that user.
  • Setup any networking you'll need; this includes pf(4), any hostname.if(5) files, dhcpd(8), etc. I don't care what you do here.
  • Install any packages you want.. GNU screen, zsh, multitail, openvpn, and ruby are some of the ones that I put on everything.
  • Enable any services you'll want in '/etc/rc.conf.local'.. I usually have something like this:
 rdate_flags="-n time.slic.com"
 watchdogd_flags="-i 3 -p 10"
 ntpd_flags=""
 named_flags=""
 isakmpd_flags="-K"
 ipsec=""
 dhcpd_flags="sis1"


Now to get to the real work.. modifying your config files and filesystem to work with the read-only root configuration.

Read-only Root Config

Login and 'sudo ksh' if you haven't already: you'll need to perform a number of steps,
which I'll detail below..

 # cp /etc/rc /etc/rc-dist
 # ftp -o /etc/rc http://wtf.hijacked.us/random/OpenBSD-ro-rc/4.7-rc
 # cp /dev/MAKEDEV /etc/MAKEDEV
 # touch /var/run/ntpd.drift
 # touch /var/run/dhcpd.leases
 # touch /var/run/dhclient.leases.vr0
 # touch /var/run/dhclient.leases.vr1
 # touch /var/run/dhclient.leases.vr2
 # touch /var/run/dhclient.leases.vr3
 # ln -s /var/run/dhclient.leases.vr0 /var/db/dhclient.leases.vr0
 # ln -s /var/run/dhclient.leases.vr1 /var/db/dhclient.leases.vr1
 # ln -s /var/run/dhclient.leases.vr2 /var/db/dhclient.leases.vr2
 # ln -s /var/run/dhclient.leases.vr3 /var/db/dhclient.leases.vr3
 # ln -s /var/run/dhcpd.leases /var/db/dhcpd.leases
 # ln -s /var/run/ntpd.drift /var/db/ntpd.drift
 # pkill -9 cron
 # mv /var/cron /var/cron-dist
 # rm -f /var/cron-dist/tabs/.sock
 # cp -Rp /var/cron-dist /var/log/cron-running
 # ln -s /var/log/cron-running /var/cron
 # /usr/sbin/rndc-confgen -a -t /var/named
 # chmod 0640 /var/named/etc/rndc.key
 # mv /var/named /var/named-dist
 # mkdir /var/named
 # cat /etc/fstab | sed '1,$s/\/ ffs rw/\/ ffs ro/g' >/etc/fstab
 # mv /home /cfhome
 # mkdir /home
 # cat /etc/syslog.conf | grep -v -e xferlog -e lpd-errs >/etc/syslog.conf
 # cat /etc/newsyslog.conf | grep -v -e xferlog -e lpd-errs >/etc/newsyslog.conf
 # reboot

There.. if you did everything correctly and didn't do anything too funny with your system
before setting up read-only-root, things should come up with *no errors during boot*.. good luck.

I recommend leaving the serial console connected for a while. At least until you're used to
managing this setup, it'll be helpful.

Maintaining Your Soekris

From time to time, you'll obviously have to make changes to the thing; and it isn't very cool to have to reboot into
single-user and remount your filesystem read-write everytime this needs to be done. In fact, thats dumb.. BUT: "There's Another Way"..

Remounting the filesystem read-write on a live system

This should work in any case, and let you modify to your heart's content.. 

 # mount -uw /

Remounting the filesystem read-only on a live system

This will only work if you haven't started anything thats writing at the moment.. 

 # mount -ur /
Retrieved from "http://wtf.hijacked.us/wiki/index.php?title=OpenBSD_Soekris_Read_Only_Root&oldid=827"